AI summary by TwinMind
11. Dopant Diffusion - Review Atomic Scale Models, Profile Measurement Techniques
MIT OpenCourseWare
1h 16m 2s
Course Structure and Chapter Overview
- Final lecture on Chapter 7 diffusion (not final diffusion lecture overall)
- Diffusion continues in Chapter 8 with ion implantation
- Diffusion described as biggest topic in course for complexity/modeling depth
- Students should be finishing Chapter 7 reading
Review of Fermi Level and High Concentration Effects
- Effects become important when carrier concentration (n or p) > ni at diffusion temperature
- Fermi level movement in bandgap responds to doping level
- Higher doping increases point defect concentration
- Increased point defect concentration increases dopant diffusivity
- Leads to box-like shaped profiles
- Concentration dependent diffusion mechanism:
- As dopant diffuses outward, concentration drops
- Fermi level moves, total point defect concentration decreases
- Creates steep profile edges
Oxidation Enhanced Diffusion (OED) and Related Phenomena
- OED effects explained by atomic scale diffusion models
- Oxidation injects excess silicon interstitials into bulk
- Thermal nitridation injects vacancies into bulk
- Dopant diffusion mechanisms:
- Boron and phosphorus: fi (fraction interstitial) ≈ 1
- Antimony: fv (fraction vacancy) ≈ 1, fi ≈ 0.2
Atomic Scale Diffusion Mechanisms
Vacancy-Assisted Mechanism
- Chemical equation: A + V ⇌ AV pair
- A = substitutional dopant (immobile alone)
- V = vacancy
- AV pair = mobile species
- Key assumption: dopants don't diffuse without pairing with point defects
- Dopant hops into vacant site, vacancy moves, enabling dopant migration
Interstitial-Assisted Mechanisms
- Chemical equation: A + Si_i ⇌ AI pair
- Two sub-mechanisms:
- Kickout mechanism: Silicon interstitial kicks out dopant, they exist as pair
- Interstitialcy mechanism: Dopant and silicon atom share substitutional site
Experimental Evidence and Surface Process Effects
OED Experimental Setup
- Local oxidation experiments using patterned silicon nitride masks
- Buried marker layers (typically 0.5 μm deep) to measure diffusion extent
- Results show enhanced diffusion under oxidizing regions vs inert regions
- Stacking fault growth correlates with interstitial injection
Nitridation Effects
- Opposite effect to oxidation
- Boron diffusion retarded, stacking faults shrink
- Evidence for vacancy injection
Atomistic Diffusion Modeling
Mathematical Framework
- Da = Da* [fi(Ci/Ci) + fv(Cv/Cv)]
- Da = effective diffusivity under perturbed conditions
- Da* = equilibrium diffusivity (inert conditions)
- fi, fv = fractional contributions (fi + fv = 1)
- Ci/Ci, Cv/Cv = point defect supersaturation ratios
Two-Dimensional Effects and Recombination
- Surface recombination rates differ between:
- Oxidizing interfaces
- Inert interfaces
- Bulk recombination
- Stripe width experiments reveal recombination rate differences
- Interstitial vs vacancy recombination behavior varies significantly
Boron Diffusion Case Study
Chemical Reactions
- B⁻ + Si_i⁰ ⇌ (BSi_i)⁻ pair
- B⁻ + Si_i⁺ ⇌ (BSi_i)⁰ pair
- Total flux = flux of both pair types
Complex Diffusion Equation
- Full Supreme-4 equation includes:
- Concentration-dependent diffusivity
- Interstitial supersaturation effects (Ci/Ci*)
- High concentration effects (1 + βp/ni)
- Electric field effects (∂/∂x ln[...])
- Far more complex than simple Fickian D∂C/∂t = D∂²C/∂x²
Reverse Short Channel Effect (RSCE)
Background
- Normal short channel effect: VT decreases as channel length (L) decreases
- Reverse effect: VT increases in certain L range during device scaling
- Caused by non-uniform boron redistribution due to point defect gradients
Physical Mechanism
- Source/drain implants inject excess interstitials
- Interstitial flux gradients drag boron toward surface
- Shorter channels more affected due to proximity to source/drain
- Results in 3-4x higher boron concentration at surface for 0.18 μm vs 1 μm devices
Modeling Results
- Two-dimensional Supreme simulations explain experimental VT variations
- Interstitial flux arrows show diffusion from source/drain regions
- Peak boron profile shifts upward toward surface
- Non-Fickian behavior: peak position changes (impossible with normal diffusion)
Profile Measurement Techniques Overview
Requirements
- Critical for model validation and process control
- One-dimensional depth profiling well-developed
- Two-dimensional mapping still challenging
Measurement Categories
- Chemical techniques: Measure total dopant atoms/cm³
- Electrical techniques: Measure carrier concentration (electrons/holes)
- Note: Chemical ≠ electrical due to activation and compensation effects
Secondary Ion Mass Spectrometry (SIMS)
Dynamic SIMS Operation
- Primary ion beam sputters surface at constant rate (~5 Å/sec)
- Mass spectrometer analyzes ejected secondary ions
- Time-to-depth conversion using sputter rate calibration
- Intensity-to-concentration conversion using implanted standards
Primary Ion Selection
- O₂⁺ beam: Enhances positive ion production (Groups I-III, transition metals, boron)
- Cs⁺ beam: Enhances negative ion production (Groups IV-VII, arsenic)
Detection Capabilities
- Best sensitivity: parts per billion to parts per trillion
- Spot size: typically 100 μm
- Depth resolution: ~100 Å for shallow junctions
Calibration Requirements
- Always relative measurement, requires standards
- Ion implanted samples provide accurate dose standards (e.g., 1×10¹⁴ P/cm²)
- Matrix effects: ionization yield varies with host material
- Same-day calibration essential
Depth Resolution Factors
- Element and matrix dependence
- Ion damage and mixing effects
- Sputter depth effects (crater roughening)
- Surface roughness accumulation
- Recent improvements: ultra-low energy SIMS, sample rotation, beam rastering
Electrical Measurement Techniques
Spreading Resistance Profiling (SRP)
- Beveling + two-probe resistance measurement
- Measures carrier concentration vs depth
- Depth resolution: ~1000 Å (worse than SIMS)
- Requires calibration curves (resistivity → carrier concentration)
- Limited to well-characterized materials (single crystal silicon)
Advanced 2D Techniques
Cross-section TEM with Chemical Etching
- Qualitative junction delineation
- ~10¹⁹/cm³ concentration contours visible
- Time-consuming, not quantitative
Scanning Capacitance Microscopy (SCM)
- AFM tip + local C-V measurements
- Beveled samples for depth information
- Spatial resolution limited by probe size and fringing fields
- Requires sophisticated electromagnetic modeling
- Still under development
Measurement Technique Comparison
SIMS Advantages/Limitations
- Excellent 1D depth profiling
- Best sensitivity and depth resolution
- Matrix effects require careful calibration
- Near-surface artifacts (improving)
Spreading Resistance Advantages/Limitations
- Measures active carriers (not total dopant)
- Good sensitivity
- Poor depth resolution
- Difficult for shallow junctions
- Requires electromagnetic modeling
2D Techniques Status
- Scanning probe methods show promise
- Still require beveling
- Advanced modeling under development
- Quantitative 2D profiling remains challenging
