AI summary by TwinMind
Etch: Lithography's Unheralded Sibling
Asianometry
18m 22s
Introduction to Semiconductor Etching
- Lithography transfers chip design onto photoresist-coated wafer
- Etching engraves design into wafer's layers using liquid or plasma gas etchant
- Removes unwanted parts of chip design to bring it to life
Early Wet Etching Era
- Beginning only had wet etching technology
- Process: dunk wafer into heated $10,000 quartz bath full of acid chemicals
- Acid type depends on material being etched (bare silicon, silicon dioxide, aluminum interconnects)
- Shake wafer like Polaroid picture to bring fresh etchant to surface
- Shaking loosens gas bubbles that prevent etching and slow etch rate
- After completion: wash off acid, dry wafer using spin dryer
- Goal: high and consistent etch rates across every wafer and run
- Evolution: switched from immersion etching to spray etching for more continual fresh etchant supply
Wet Etching Advantages and Limitations
- Advantages:
- Chemical reaction is selective - can etch one material without affecting other layers
- Disadvantages:
- Difficult to consistently control chemical reaction
- Hard to automate, effectiveness depends on operator skill
- Environmental concerns: particle contamination and toxic waste
- Critical limitation: isotropic etch profile (etches equally in all directions)
- Cannot guide etching in proper direction
- Undercutting occurs when resist lines are thin enough
- Hurts imaging resolution
Transition to Dry Etching
- Undercutting became serious issue at 5 micrometer process node for 16K DRAM
- Industry decided wet etch alone cannot achieve resolution for next node (3 micrometer/64K DRAM)
- 1967: Steve Irving at Signetics demonstrated gas plasma to strip photoresist from silicon surface
- Process called "ashing" - reduces things to ash
- Concept borrowed from using gas plasma to ash organic parts of animal tissue for testing
- Purchased plasma equipment from Tracer Lab (LFE Corporation subsidiary)
- Successfully removed photoresist without destroying crystal structure
Plasma Technology Fundamentals
- Plasma is fourth state of matter
- Semiconductor plasmas are ionized (gas atoms become charged by losing/gaining electrons)
- Created by exposing gas to powerful RF field (usually 13.56 MHz) rather than high temperatures
- Low temperature plasmas: 50-250°C, materials react at lower temperatures/energies than gas/liquid states
- Example: CF4 (carbon tetrafluoride) etching silicon
- Normal gaseous CF4 cannot etch strong silicon-silicon bonds
- Plasma state breaks carbon-fluoride bonds into fluorine, CF3, CF2
- Ion bombardment weakens silicon bonds
- Result: silicon tetrafluoride gas + carbon layer
- Oxygen pumped in reacts with carbon to create CO2
Early Plasma Equipment Development
- 1971: Steve Irving received patent for gas plasma vapor etching
- Left Signetics for International Plasma Corporation, developed first plasma etch for silicon nitride (LED screens)
- First equipment were crossovers from other industries
- 1972: First specialized plasma etching equipment - Barrel type reactors
- Barrel-shaped plasma chamber with external RF coils (prevent contamination)
- Wafers loaded like dishes in dishwasher
- 1975: Market only $1.6 million - customers thought plasma etching was for healthcare, not semiconductors
Barrel Etcher Limitations
- Performed well only for photoresist stripping (still used today)
- Poor performance for actual etching:
- No good temperature control
- Non-uniform etching across wafer
- Radiation damage to wafers
- Still isotropic - disqualified as credible wet etch replacement
Parallel Plate Reactor Innovation
- 1973: Alan Reinberg at Texas Instruments developed parallel plate reactor (also called radial flow reactor)
- Inspired by chemical vapor deposition work
- Design: wafers on platter with RF electrode underneath, hole at center for gas flow
- Second set of electrodes above wafers
- RF electrode accelerates plasma ions downward, physically bombarding wafers
- Triggers chemical reaction between etchant plasma and substrate
- Key benefit: anisotropic etch - chemical reaction selectiveness while guiding etch in single direction
- Evolved into reactive ion etch (RIE) system
Market Breakthrough
- 1975: IBM team led by Dr. Hua Nanu produced 8 kilobit memory with 1-1.5 micrometer line dimensions
- Used cutting-edge technologies:
- Electron beam lithography for pattern transfer
- Reactive ion etch and ion implantation for chip features and electrical properties
- Demonstration showed future potential, manufacturers quickly transitioned from wet to dry etch
Dry Etching Challenges
- Plasma damage: Silicon substrate damage and residual metal impurities
- Solution: post-etch cleaning step
- Methods: oxygen/hydrogen plasma blast + wet acid + hot bake, or lasers
- Equipment speed: Too slow compared to barrel batch processing
- Early RIE machines processed one wafer at a time very slowly
- Tools cost over $1 million each
- Poor throughput made economic justification difficult
Plasma Density Enhancement Efforts (Early 1980s)
- Magnetically Enhanced RIE (MARIE):
- Added magnetic field to intensify plasma and enhance etch
- Problem: magnetic fields parallel to wafer created non-uniform plasma
- Rotating magnet damaged wafer - became dead end
- Electron Cyclotron Resonance (ECR):
- 1950s: Oak Ridge National Lab invented for fusion research
- Uses microwaves and magnetics to produce high density plasma in separate chamber
- 1982: NTT filed patent, licensed to Hitachi
- Hitachi rebranded as "microwave plasma etching" for 4 megabit DRAM at 800nm node
- Late 1980s-early 1990s: Sematech funded Oak Ridge commercialization efforts
- Problems: too complicated, huge magnetic coil, non-uniform etch rates
Inductively Coupled Plasma (ICP)
- Late 1980s modification of ECR
- Magnetic coil at top of chamber produces high density plasma using electromagnetic induction
- Became industry's dominant way to do RIE with high density plasma
- Applied Materials, Lam Research, other vendors continue advancing plasma density without wafer damage
Deep Reactive Ion Etching (DRIE)
- Descended from RIE, developed in MEMS world
- MEMS artists needed complex geometries in silicon (deep holes for tether beams)
- Existing methods produced v-shaped holes
- 1990s: German company Bosch developed DRIE (Bosch process)
- Process: Cycles through two steps (few seconds each)
- Fire high density plasma mix of etchant and ions (creates round crater)
- Apply inhibitor (Teflon-like) coating to crater, nullifies acid
- Fire etchant+ion plasma again - ions break through inhibitor at bottom only
- Side walls protected by untouched inhibitor
- Result: Deep hole with characteristic scallop sidewall
- Applications:
- Through Silicon Vias (TSVs) for die-stacked chips like Nvidia AI accelerators
- Thin, deep trenches for leading-edge DRAM chips
Future Challenges and Atomic Layer Etching
- Moore's Law progression requires smaller, more precise, and fast etching
- Atomic Layer Deposition (ALD) builds layers atom by atom
- Atomic Layer Etching (ALE) tears down thin layers atom by atom
- ALD widely used on fab floors, ALE still working through quirks
- Sign that etch (lithography's unheralded sibling) has vibrant future ahead
