AI summary by TwinMind
Intel’s Next Breakthrough: Backside Power Delivery
Asianometry
19m 13s
Intel's Innovation History & 18A Node Introduction
- Intel historically strong at R&D, willing to take risks on new technologies
- Previous innovations: high-K metal gate, FinFET transistor, strained silicon
- 18A node features two major innovations:
- Gate all-around transistor (covered in separate video)
- Backside power delivery network (BSPN) - focus of this discussion
Power Delivery Fundamentals
- Transistors need stable power supply at correct voltage to switch properly
- Power = current × voltage
- Voltage acts like pressure pushing electrons through wires
- Critical voltage requirements:
- 1% drop in gate voltage = 1% decline in chip operating frequency
- Insufficient voltage causes timing errors, blue screens
- Excessive voltage increases power consumption (proportional to voltage²)
- Too high voltage causes gate oxide breakdown (reliability wall)
- Different chip sections have different voltage needs (power domains)
- Mobile SoCs may have hundreds of power domains
- Power delivery must be within 5-10% margin, delivered stably/efficiently
Current Power Delivery Architecture
- Power flows from power supply → socket pins → chip packaging → transistors
- Uses network of metal interconnects and vias throughout chip
- Vias connect between IC's multiple layers (10-20 layers typical)
- Supporting components:
- Voltage regulator modules: step voltage up/down for different domains
- Decoupling capacitors: smooth network, handle voltage spikes from inductance
- Entire system called Power Delivery Network (PDN)
Power Delivery Challenges
- Metal wires suffer from parasitic inductance and resistance
- Resistance causes IR drop - voltage lower at wire end than start
- Traditional arrangement: front side power network
- Power travels from top down to transistors on bottom
- Deeper layers have smaller wires
- Moore's Law progression creates problems:
- Billions of transistors need power
- More interconnect layers required
- Power interconnects interfere with signal interconnects
- Interconnects now ~20nm diameter causing substantial IR drops
Metal Interconnect Limitations
- Industry moved from aluminum to copper 20 years ago for lower resistance
- Copper bulk resistivity: 1.1664 microohms per cm
- At 20nm scale, electrons scatter more (reduced mean-free path)
- Copper requires barrier layers (tantalum nitride) with high resistance
- Designers must trade signal resources for robust power systems
IMC Belgium's Innovations
- Semiconductor research center pioneered buried power rails and BSPN
- Two-step approach: buried power rails first, then full BSPN
Buried Power Rails Technology
- Utilizes space beneath silicon surface (previously underutilized)
- Standard cells measured in tracks (6 tracks high at 3nm node)
- Power rails take up 2 tracks, cramping standard cells
- Process:
- Dig trenches into silicon substrate using shallow trench isolation
- Use atomic layer deposition for metals in trenches
- Done during front end of line (FEOL) stage
- High temperatures require tungsten or ruthenium (not copper)
- Advantages:
- Tungsten/ruthenium have lower resistance than copper at 20nm
- Tungsten has good supply chain
- Ruthenium needs minimal barrier layer
- Challenges:
- Fabs never did metallization in front end
- Metal contamination concerns
Backside Power Delivery Network (BSPN)
- Separates all power interconnects from signal interconnects
- Moves power network underneath silicon transistor layer
- Connects via nano through-silicon vias (TSVs) through silicon wafers
- Performance improvements:
- 8% better power consumption vs standard front side delivery
- IR drop reduced to 15% of front side configuration
- ARM showed 7x improvement in 2019 simulations
- Additional benefits:
- More space for signal interconnects reduces parasitic capacitance
- Improved signaling speed
Precedent: Image Sensor Backside Illumination
- Similar concept pioneered in CMOS image sensors (2009)
- Companies: OmniVision, Sony Semiconductor Solutions
- Problem: wiring blocked light from reaching photo diodes
- Solution: move wiring behind photo diode substrate
- Sony's process:
- Bond second wafer on top
- Flip and thin wafer to 5-10 micrometers
- Grind with specialized equipment (Disco company grinders)
- First commercial use: iPhone 4 (2010)
BSPN Manufacturing Process
- More challenging than image sensors: thin to 500nm (0.5 micrometers)
- Detailed process steps:
- Start with ordinary wafer
- Grow 50nm silicon germanium layer
- Add thicker pure silicon capping layer
- Cut buried power rails using shallow trench isolation
- Metalize trenches with tungsten/ruthenium using ALD
- Bond carrier wafer on top
- Flip assembly
- Grind down original wafer backside (grinder → polisher → etch)
- Wet etch with acid to expose capping layer
- Use lithography to pattern TSV locations
- Bosch process etching for TSVs (~90nm wide)
- Clean, line with barrier, metalize with copper
Industry Implementation Timeline
- Intel's approach:
- Calls their version "PowerVia"
- First introduced in 20A process node (precedes 18A)
- 18A will have both BSPN and gate-all-around transistors
- TSMC's approach:
- More conservative introduction
- N2 node (2025): introduces gate-all-around transistors
- N2P node (2026): adds BSPN
- Intel expected to reach market first with both innovations
Design Challenges & Future Impact
- Massive EDA (Electronic Design Automation) design challenge
- Customers must port and redesign existing power delivery networks
- Benefits justify complexity
- Technology enables 3D stacking capabilities (similar to image sensors)
- Represents ongoing trend, not one-time boost
