AI summary by TwinMind

Lecture 12: Magnetics, Part 4

MIT OpenCourseWare

50m 54s

Introduction to Magnetic Loss

  • Topic: magnetics loss in power electronics components
  • Focus: scratch surface of deep topic (full chapter in Principles of Power Electronics Ch. 20)
  • Goal: provide basic information for magnetic component design awareness
  • Applications: inductor/transformer design for converters

Importance of Magnetic Loss

  • Dominant loss source: magnetic components typically main loss source in converters
  • Size limitation: loss often determines component size (thermal constraints)
  • Two main categories: winding loss and core loss

Basic Winding Loss (DC Analysis)

  • DC resistance calculation: R = ρL/A (resistivity × length / area)
  • Temperature dependence: copper resistivity increases ~40% per 100°C rise
  • Power calculation: P = I²rms × R
  • Design trade-off: wire gauge vs. length vs. loss

Current Density Limitations

  • Thermal constraints: current density limited by heat transfer
  • Scale dependence: smaller components allow higher current densities
  • Typical values: ~500 A/cm² for small components, 100-200 A/cm² for larger
  • Rule of thumb: start with current density estimate, verify thermal performance
  • Chart reference: RM core data showing power density vs. size

Skin Effect

  • Mechanism: AC current concentrates at conductor surface due to eddy currents
  • Physical cause: changing magnetic flux in conductor generates opposing eddy currents
  • Current distribution:
    • DC: uniform across wire cross-section
    • AC: exponential decay from surface (J ∝ e^(-x/δ))
  • Skin depth formula: δ = √(σ/(πμf))
    • Decreases as 1/√f
    • Determines penetration depth of current
  • AC resistance: RAC = RDC × (W/δ) when W >> δ
  • Frequency scaling: RAC ∝ √f in high-frequency regime

Skin Effect Demonstration

  • Experimental setup: aluminum block as single-turn secondary
  • Measurement: magnetic field probe moved across conductor
  • Results: 60 Hz vs 240 Hz comparison showed ~2× skin depth difference
  • Frequency relationship: 4× frequency change → 2× skin depth change

Litz Wire Solution

  • Construction: multiple insulated strands woven/twisted together
  • Transposition: each strand spends equal time on surface vs. interior
  • Strand sizing: diameter ≈ skin depth for skin effect mitigation
  • Applications: high-frequency, high-current designs

Proximity Effect

  • Definition: eddy current loss in conductor due to external magnetic fields
  • Mechanism: H-field from nearby conductors induces circulating currents
  • Transformer example: layered windings create increasing H-field across window
  • Field distribution: H-field builds up layer by layer (1H, 2H, 3H units)
  • Loss scaling: approximately proportional to square of layer count
  • Impact: can increase AC resistance 10-30× over DC value

Proximity Effect Mitigation

  • Wire sizing: often requires thinner conductors (≤3 skin depths)
  • Counter-intuitive: thinner wire can reduce total loss
  • Design challenge: more copper can increase loss due to proximity effect

Core Loss Fundamentals

  • Energy calculation: ∮ H·dB per cycle (hysteresis loop area)
  • Physical mechanism: work done moving magnetic domains
  • Hysteresis loop: B-H relationship shows energy loss per cycle
  • Volume scaling: loss proportional to core volume

Core Loss Types

  • Hysteresis loss:
    • Low frequency: proportional to frequency
    • High frequency: frequency dependence varies with material
    • Domain movement and associated eddy currents
  • Eddy current loss in core:
    • AC flux through conductive core material
    • Circular currents oppose flux changes
    • Significant when core dimensions ≈ skin depth

Eddy Current Mitigation in Cores

  • Laminations: thin insulated sheets stacked together
  • Sizing: lamination thickness << skin depth
  • Applications: 60 Hz transformers, electric machines use laminated steel
  • High frequency: ferrites naturally non-conductive, less concern

Empirical Core Loss Modeling

  • Formula: Pv = K × f^α × B^β (power per unit volume)
  • Parameters: K, α, β determined experimentally
  • Data presentation: loss curves vs. flux density at various frequencies
  • Design process: look up loss from manufacturer data/curves
  • Measurement dependency: very empirical, hard to predict from first principles

Core Loss Demonstration

  • Setup: inductor with current (∝H) on x-axis, integrated voltage (∝B) on y-axis
  • Results: visible hysteresis loop showing B-H relationship
  • Saturation: loop shape changes as core approaches saturation
  • Frequency dependence: loop shape varies with frequency

TwinMind

Get summaries like this for your own meetings

TwinMind takes notes in the background during meetings, lectures, and calls, then writes the summary for you.

Free plan to get started

No bot joins your calls

Phone, desktop & Chrome apps

Your next meeting, summarized like this

TwinMind listens in the background and turns meetings, lectures, and calls into searchable notes you can chat with. Start free.

Available on phone, desktop & Chrome

Your next meeting, summarized like this

TwinMind listens in the background and turns meetings, lectures, and calls into searchable notes you can chat with. Start free.

Available on phone, desktop & Chrome

Your next meeting, summarized like this

TwinMind listens in the background and turns meetings, lectures, and calls into searchable notes you can chat with. Start free.

Available on phone, desktop & Chrome