AI summary by TwinMind

Lecture 29: EMI Filters, Part 2

MIT OpenCourseWare

50m 18s

EMI Testing Setup and Standards

  • EMI testing requires Line Impedance Stabilization Network (LISN) for repeatability
    • LISN contains L_lisn and C_lisn components
    • Connected to 50-ohm spectrum analyzer
    • Eliminates source impedance variability during testing
    • Separate LISN on hot lead and ground lead in most systems
  • Conducted EMI testing typically covers 150 kHz to 30 MHz frequency range
    • Military standards may extend to lower frequencies
    • Test setup details specified by standards
  • Current limits: converter may draw tens of amps, but allowed current back into source limited to tens of microamps

Basic Filter Design Principles

  • Simple capacitor insufficient for EMI compliance
  • Basic LC filter building block: filter capacitor (CF) and filter inductance (LF)
  • Attenuation characteristics:
    • DC: everything passes back (magnitude = 1)
    • Above cutoff frequency (1/√(LF·CF)): rolls off at -40 dB/decade
    • Capacitor impedance falls 10x per decade frequency increase
    • Inductor impedance rises 10x per decade frequency increase
    • Results in 100x attenuation per 10x frequency increase

Component Parasitics Impact

  • Internal parasitics degrade filter performance
  • Filter capacitor parasitics:
    • ESR (R_r) reduces rolloff to -20 dB/decade at high frequencies
    • Parasitic inductance (L_parasitic) creates current divider with LF
    • Performance flattens out instead of continuing rolloff
  • Parasitics sources:
    • Internal component parasitics
    • Layout parasitics (circuit board placement)
    • Parasitic inductance and resistance
    • Parasitic capacitance

Resonance and Damping Issues

  • At cutoff frequency (1/√(LF·CF)):
    • LF and CF appear as open circuit at resonance
    • Current gain (iy/ix) approaches infinity
    • Causes huge circulating currents and instability
  • Output impedance ZX behavior:
    • Low frequencies: ωLF (inductive)
    • High frequencies: 1/(ωCF) (capacitive)
    • At resonance: approaches infinity (open circuit)

Capacitive Damping Strategy

  • Add damping resistor (Rd) in series with damping capacitor (CD)
  • Damping leg provides:
    • Near cutoff: CD acts as short circuit, Rd provides damping
    • At DC: CD acts as open circuit, no DC current loss
  • Design equations:
    • R_out = √(LF/CF) (characteristic impedance)
    • n = CD/CF (capacitor ratio)
    • Rd_opt = R_out × √[(2+n)×(4+3n)/(2n²×(4+n))]
    • ZX_max = R_out × √[(2+n)/n]
  • Typical CD values: 2-10 times CF for adequate damping
  • Component selection considerations:
    • CF: high-frequency performance critical (ceramic/film capacitor)
    • CD: operates near cutoff, can use electrolytic with higher ESR

Inductive Damping Alternative

  • Series combination of LD and RD in parallel with filter
  • Design requirements: LD < LF
  • Near cutoff: LD appears as short circuit, RD provides damping
  • High frequencies: LD becomes inductive, maintains rolloff
  • Advantages: LD is small, carries no DC current
  • Disadvantages: degrades filtering performance slightly above cutoff (-20 dB/decade initially vs -40 dB/decade)

Constant Power Load Effects

  • Power converters act as constant power loads: Pin × VN = Pout
  • Small-signal input resistance: Rvel = -Pout/Iin² (negative resistance)
  • Negative input resistance destabilizes filter
  • Stability condition: net damping resistance must be positive
    • Rnet = (Rd × RL)/(Rd + RL) > 0
    • Requires |Rd| < |RL| for stability
  • Maximum filter output impedance must be well below |Pout/Iin²|

Practical Design Considerations

  • Filter cutoff frequency must be well below switching frequency
  • Converter operates in hundreds of kHz, filter cutoff in kHz range
  • Real-world source impedance affects filter design
  • Filter output impedance ZX appears as source impedance to converter
  • Sufficient conditions for decoupled design:
    1. ZX_max << |negative input resistance| under perfect control
    2. Fixed duty ratio input impedance < filter output impedance across all frequencies

Demonstration Results

  • Live demonstration showed oscillation without damping leg
  • With damping: stable input voltage VN ≈ VS
  • Without damping: severe oscillations in input voltage
  • Emphasizes critical importance of proper filter damping in real systems

TwinMind

Get summaries like this for your own meetings

TwinMind takes notes in the background during meetings, lectures, and calls, then writes the summary for you.

Free plan to get started

No bot joins your calls

Phone, desktop & Chrome apps

Your next meeting, summarized like this

TwinMind listens in the background and turns meetings, lectures, and calls into searchable notes you can chat with. Start free.

Available on phone, desktop & Chrome

Your next meeting, summarized like this

TwinMind listens in the background and turns meetings, lectures, and calls into searchable notes you can chat with. Start free.

Available on phone, desktop & Chrome

Your next meeting, summarized like this

TwinMind listens in the background and turns meetings, lectures, and calls into searchable notes you can chat with. Start free.

Available on phone, desktop & Chrome