AI summary by TwinMind
Lecture 7: DC/DC, Part 3
MIT OpenCourseWare
50m 8s
Buck-Boost Converter Review
- Buck-boost converter topology: input V1, switch, diode, output V2, filter capacitor, inductor with current I
- Assumes L and C are large (approximately infinite) for initial analysis
- DC values: IL = |I1| + |I2|, VC = |V1| + |V2|
- Switch and diode stress analysis:
- V_switch_max = V_D_max = VC = |V1| + |V2|
- I_switch_max = I_D_max = |I1| + |I2|
Buck vs Boost Converter Comparison
- Buck converter: V_switch = V_D = V1, I_switch = I_D = I2
- Boost converter: V_switch = V_D = V2, I_switch = I_D = I1
- General rule for buck/boost:
- V_switch = V_diode = max(|V1|, |V2|)
- I_inductor = I_switch = I_diode = max(|I1|, |I2|)
Buck-Boost vs Buck/Boost Stress Analysis
- Buck-boost sees higher component stresses
- Buck-boost: sum of input/output voltages and currents
- Buck/boost: maximum of input/output voltages and currents
- Reason: Buck-boost stores all energy in inductor temporarily
- Buck/boost have direct current path from input to output
- Buck-boost requires more energy storage for same conversion function
Finite Component Analysis Introduction
- Need to abandon infinite L and C assumption for practical design
- Component sizing considerations:
- Ripple limitations
- Transient dynamics
- Component size, loss, and cost
- Focus on ripple analysis for component sizing
Boost Converter Ripple Analysis
- Diode current ID waveform: 0 during DT, I during (1-D)T
- Average diode current: (1-D)I
- AC model: ID_tilde = -[(1-D)I] during DT, +[DI] during (1-D)T
- Filter design: 2πf_switch >> 1/RC for proper filtering
Capacitor Ripple Calculation
- Capacitor voltage ripple VC_tilde: triangular waveform
- ΔVC_peak-to-peak = D(1-D)IT/C
- Component sizing: C ≥ D(1-D)IT/ΔVC_peak-to-peak
- Ripple current flows entirely into capacitor (approximation)
Inductor Ripple Calculation
- Inductor voltage VX: 0 during DT, VC during (1-D)T
- AC component: VX_tilde = -(1-D)VC during DT, +DVC during (1-D)T
- ΔIL_peak-to-peak = (1-D)DVCT/L
- Component sizing: L ≥ (1-D)DVCT/ΔIL_peak-to-peak
Cross-Coupling Approximations
- Ignoring inductor current ripple when calculating capacitor voltage ripple is valid
- Ignoring capacitor voltage ripple when calculating inductor current ripple is valid
- Peak-to-peak ripple values remain accurate despite approximations
- Waveform curvature changes slightly but peak values unchanged
Ripple Ratio Definition
- Ripple ratio Rx = (ΔX_peak-to-peak/2)/X_DC
- Normalized measure of ripple relative to DC value
- X_peak = X_DC × (1 + Rx)
- Literature varies in definition (some use ΔX_peak-to-peak/X_DC)
Energy Storage Analysis
- Component size roughly proportional to energy storage
- Capacitor energy: EC = ½CV²_peak
- For boost converter: EC = D×P_out×T/4 × (1+Rc)²/Rc
- Energy storage dependencies:
- Proportional to output power
- Proportional to duty cycle D (higher conversion ratios)
- Inversely proportional to switching frequency
- Inversely proportional to ripple ratio (smaller ripple = more energy)
Design Trade-offs
- Lower switching frequency → larger components
- Lower ripple requirements → larger components
- Higher conversion ratios → larger components
- Buck-boost requires significantly more energy storage than buck/boost
- Component sizing affects converter size, cost, and efficiency
