AI summary by TwinMind
This Thing is Crazy Fast - Kodak Part 3- Smarter Every Day 286
SmarterEveryDay
59m 56s
Introduction and Series Overview
- Third video in three-part series at Kodak film factory in Rochester, New York
- Previous videos covered backing manufacturing and light-sensitive coating application
- Current video focuses on slitting, perforation, can manufacturing, and final packaging
- All processes must occur in darkness to protect light-sensitive coating
- Destin filming using actual Kodak film throughout process
Film Slitting Process
- Operator: Tim (30 years experience working in dark)
- Engineer: Patrick (learning from operators)
- Input: 54-inch wide rolls from coating department, 12,000 ft per casket
- Process: Large rolls slit into 35mm width strips
- Film travels up and over slitting machine to knife assembly
- Blades cut film into even/odd banks
- Approximately 5 ft per 35mm roll
- Edge waste sent to silver recovery
- Tension Management: Critical for proper slit width
- Directional clutches maintain tension
- Web steering system keeps film centered
- Output: 35mm width rolls on carts, transported via automated rail system
Slitting Machine Blade Assembly
- Configuration: Upper and lower knife sets in frame
- Cutting Method: Shear cutting with precise geometry
- Blade Contact: Film wraps around lower roller (~100 degrees contact)
- Maintenance: Blades require precise alignment and regular maintenance
Perforation Process (Adding Sprocket Holes)
- Operator: Matt (26 years experience)
- Machine Speed: Up to 3,000 ft per minute (vs 100 ft/min on old machines)
- Process:
- Automated roll loading from rack system
- Computer reads roll information from rack card
- Determines roll length (2,000 ft, 4,000 ft, or 6,000 ft) and customer specifications
- Rounded edge cutting to prevent damage to "heart" mechanism
- Manual tape application for threading
- Automated perforation punching
Heart Mechanism (Perforation System)
- Components: Punch drum and die drum with 96 sets of punches/dies
- Precision: Months required to tune one heart assembly
- Maintenance: Individual die adjustment using specialized microscopes and jigs
- Cost: Tens of thousands of dollars per heart assembly
- Vacuum System: Removes punched film pieces through center hub
- Quality Control: Scratch test sample sent to quality lab for every roll
Film Can Manufacturing
- Raw Materials: Large metal sheets pre-printed with magazine information and DX codes
- Operator: Donovan
- Process:
- Cutting large sheets into strips
- Visual inspection of every strip
- Forming metal end caps using specialized presses
- Velvet light seal application
- Velvet comes in rolls through accumulator system
- Heated adhesive application
- Cutting velvet between strips
- Can formation using rotary dial machine
- Metal strips rolled into cylinders
- End cap attachment and staking
- One-sided assembly (open for film insertion)
Component Orientation and Assembly
- Vibration Systems: Orient can components and plastic canisters correctly
- Gravity Feed: Plastic canisters sorted by lip orientation
- Lid Orientation: Sensors detect correct lid positioning, reject incorrect ones
- Light Lock: All components pass through light-tight transfer to assembly area
Film Spooling and Assembly
- Operator: Surman
- Dual Cabinet System: Two roll system (A and B) for continuous operation
- Frame Marking: Light exposure system adds frame numbers to film
- Accumulator Systems: Multiple vacuum boxes manage film tension during start/stop cycles
- Exposure Settings: Configurable for 24 or 36 exposure rolls
- Leader Cutting: Punch and die system creates leader pattern
8-Station Rotary Assembly
- Station 1: Tape application to plastic spool center
- Station 2: Film attachment and rapid winding
- Station 3: Film cutting
- Station 4: Metal can placement over wound film
- Station 5: End cap installation for light-tight seal
- Station 6: Assembly placement in plastic canister
- Station 7: Lid application
- Station 8: Final assembly completion
- Transport: Pneumatic tube system to packaging area
Final Packaging Process
- Supervisor: Rich Colleen
- Package Types: Singles, 2-packs, 3-packs, 5-packs with various formats
- 3P Packaging Line: 12 stations continuously running
- Process Steps:
- Carton feeding with suction cup system
- Bottom flap folding with kicker arms
- Film loading (5-pack example shown)
- Metal detection verification (ensures correct count)
- Top flap folding
- Emulsion number and expiration date printing
- Glue application (top and bottom tabs)
- Mechanical compression for adhesive setting
- Quality inspection with light sensors
- Final ejection to packaging operator
Quality Control and Inspection
- Human Inspection: Every package checked for damage and print quality
- Metal Detection: Verifies correct film count in packages
- Flap Inspection: Light sensors ensure proper closure
- Scratch Testing: Sample from every roll tested in quality lab
- Visual Inspection: Multiple human checkpoints throughout process
Workforce and Culture
- Experience Range: 4 months to 45 years
- Training Model: Experienced operators teach engineers
- Team Environment: Strong family-like culture
- Production Trends: Increasing demand, working overtime
- Equipment: Reduced from 28 to 9 perforation machines due to digital transition
- Film Revival: Growing interest from Hollywood directors and photography enthusiasts
Final Product Testing
- Live Demonstration: Destin loaded fresh film directly from production line
- Camera Used: Manual 35mm camera set to ISO 400
- Photos Taken: Group photos of production team
- Quality Verification: Immediate use of just-manufactured film
Technical Specifications
- Production Speed: Up to 3,000 ft/min perforation
- Roll Sizes: 2,000 ft, 4,000 ft, 6,000 ft options
- Heart Assembly: 96 punch/die pairs, direct servo drive
- Precision Requirements: Months of tuning per heart
- Material Recovery: Silver recovery from waste perforations and edge trim
- Automation Level: Highly automated with strategic human oversight points
